b'KoverTek Tooling RangePRODUCT DESCRIPTION APPLICATIONNorester 6779 Plug Laminating Resin Suitable for Polystyrene Plugs (non Thixo)NCL 809 Sprayable CNC Putty Apply to min thickness of 8mm(2 layers) for machiningNCL 815 Extrudable CNC Putty Apply to Final thickness of 12mm for machining (3 layers)Nord 230BV Primer Plug Primer (Sprayable) Apply 450-600 MicronsNord GC 210 Sprayable Plug Lacquer Apply several thin layers to the primed plugRoar Extreme 900/ Extreme 910 Polishing Compounds For compounding from 800 grit sandingTek-Kote Mould Cleaner Mould Cleaner Solvent Wipe on Wipe OffTek-Kote Mould Sealer Semi Permanent Mould Sealer Wipe on Leave On or Wipe on SpreadTek-Kote Fast Release Semi Permanent Release Agent Wipe on Leave OnNorester GC 200 Gelcoat Iso Tooling Gelcoat (Brush Apply) For low volume cycle mouldsNorester GC 201 Gelcoat Iso Tooling Gelcoat (Spray Apply) For low volume cycle mouldsNorester GC 206 Gelcoat Vinyl Ester Tooling Gelcoat (Brush Apply) For high cycle moulds & high temp resistNorester GC 207 GelcoatVinyl Ester Tooling Gelcoat (Spray Apply) For high cycle moulds & high temp resistNorester 6842 Vinyl Ester Resin Vinyl Ester Skin Coat (Clear Thixo) For low shrink and high surface finish good mechanicals and chemical resistanceNorester 6800 Vinyl Ester Resin Vinyl Ester Skin Coat (Clear Thixo) For low shrink and high surface finish good chemical resistance and high flexural strengthPRODUCT DESCRIPTION APPLICATIONNoresterDescription: Low Styrene content PolyesterA low cost system. 2.5 : 1 Resin to Glass.8600 TA 35 laminating resin ready to use speciallyIdeal for low volume cycle moulds.recommended for the production of Moulds using Hand Lay Up or Spray Application. Thixotropic, pre accelerated ready to allow the quick production of moulds. Excellent fibre wet outand impregnation with a glass to resin ratio of 1:2. Excellent mechanical properties useful for light weight tools.NoresterTooling Resin formulated from an unsaturatedExtensively used in the Marine industry. 4 : 1 Resin to glass.RMpolyester resin. It is filled, promoted andApply min thickness of 8mm (2 layers) for machining.2000/50 pre-accelerated. Formulated for mould making. NoresterTooling Resin based on polyester resin forA rapid tooling resin with good surface appearance. Good curing.RM 2550 the production of composite moulds with lowGood mouldability, and fast wet out, resin to glass ratio 2.5 : 1 Creates shrinkage. It is a product ready to use, filled andLighter moulds with better mechanicals properties hence lower tooling pre accelerated resin costs. Superior mechanical properties due to a glass content approximately 28% higher than with conventional tooling resins.NoresterVinyl Ester Hybrid Tooling Resin especiallyDesigned to polymerize at room temperature following addition of RM 3000 formulated for producing composite moulds fornormal MEKP catalysts.Resin pre-accelerated and promoted, permits applications where high thermal and chemicala fast curing and a rapid manufacture of moulds.An easy to use resistance are required product with low shrinkage hence high surface finish of the finished mould/parts.Fast build up of Barcol hardness. Improvement of the mould rigidity and low cost of mould production. Low exotherm curing system.Low viscosity.'